American Standard Bathroom Aids 018 User Manual

Installation  
Instructions  
6028.230 6090  
6028.180 6091  
6028.244 6092  
6028.024 6093  
ACCESSORIES  
TOILET TISSUE HOLDER  
18"TOWEL BAR  
24"TOWEL BAR  
GLASS SHELF  
Thank you for selecting American-Standard...the benchmark  
of fine quality for over 100 years.  
To ensure that your installation proceeds smoothly--please  
read instructions carefully before you begin.  
Certified to comply with ANSI A112.18.1  
M968860 REV. 1.1  
Recommended Tools  
CARE INSTRUCTIONS:  
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR  
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.  
Regular Screwdriver  
Tape Measure  
10'  
Drill  
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,  
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH  
WITH A COARSE SURFACE.  
Phillips Screwdriver  
Level  
18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF AND TOILET TISSUE HOLDER  
MOUNTING BRACKET INSTALLATION  
1
2
The 18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF and TOILET TISSUE HOLDER work best if secured to a wall stud or cross brace  
within the wall, using the SCREWS (4) supplied.  
If the 18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF and TOILET TISSUE HOLDER are to be installed on a tile or plaster wall the  
ANCHORS and SCREWS should be used.  
Determine desired height and location (optional) for the accessory and mark a center line. Use the full size template supplied to mark  
hole locations for the mounting brackets. For the 24" TOWEL BAR and GLASS SHELF use 24” template. For 18” TOWEL BAR use 18”  
template. For the TOILET TISSUE HOLDER use the 7” template. If MOUNTING BRACKET (1) is secured to a stud or cross brace drill  
small pilot holes for SCREWS (2).  
For installations on drywall, use DRYWALL ANCHOR (3) and SCREWS (2) for securing MOUNTING BRACKETS (1) to wall. Place #2 Phillips  
screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with  
the wall. Place MOUNTING BRACKET (1) over DRYWALL ANCHORS (3) and insert screws provided with #2 Phillips screwdriver. See  
illustration below. Secure MOUNTING BRACKETS (1) to wall with SCREWS (2).  
For installations on tiled walls, If TILE ANCHORS (4) and SCREWS (2) are used for securing MOUNTING BRACKET (1), then  
drill two 1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall.  
Secure MOUNTING PLATES (1) to wall with SCREWS (2).  
1a  
CENTER  
LINE  
LEVEL  
INSTALL 18" TOWEL BAR, AND 24" TOWEL BAR  
5a  
6
1
Place right ESCUTCHEON (5) onto MOUNTING BRACKET (1), and secure  
with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.  
Insert each end of TOWEL BAR (8) into the CRANKS (9).  
9
Place LEFT ESCUTCHEON (5a) onto MOUNTING BRACKET (1a) and  
secure with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied.  
8
5
6092  
6093  
24" TOWEL BAR  
24"  
6
GLASS SHELF  
18"  
CENTER LINE  
(OPTIONAL TO  
FINISHED FLOOR)  
6091  
CENTER LINE  
18" TOWEL BAR  
7"  
FINISHED WALL  
6090  
TOILET TISSUE HOLDER  
9
DRILL PILOT HOLE FOR  
WOOD SCREW OR  
1/4" DIA. HOLE FOR  
ANCHOR  
7
ANCHORS (FOR TILED WALLS)  
DRYWALL ANCHORS  
TEMPLATE  
FINISHED WALL  
5
5a  
CENTER  
LINE  
4
1
3
2
1
DRILL PILOT HOLE FOR  
WOOD SCREW (1) OR  
1/4" DIA. HOLE FOR  
ANCHOR (4)  
4
3
6
SLOT  
 

3M Model Vehicle MDS100 User Manual
Aiphone Intercom System VY 10EM User Manual
Alcatel Carrier Internetworking Solutions Cell Phone 535 735 User Manual
Alliance Laundry Systems Washer WF150 User Manual
Alto Shaam Fryer ASF 60G User Manual
ATN Binoculars ATN MArs x4 User Manual
Bakers Pride Oven Outdoor Storage CA71 IN39 User Manual
Barco Projector R5075236_r03 User Manual
BB Electronics Computer Hardware 232CC1A User Manual
Behringer Electronic Keyboard CDP2400USB User Manual